Saniflo 089 Gebrauchs- und Pflegehandbuch PDF herunterladen (Seite 4)

DESCRIPTION

The SANICUBIC

1 is a lift station designed

to evacuate effluent from residential and

light commercial applications.

Please comply with all the installation

and maintenance specifications set out

in these instructions, and especially the

information marked with the following

signs:

» Failure to comply with this

information could entail safety

hazards for personnel,

» Information warning of the

presence of an electrical hazard,

» Instructions only for qualified

professional specialists,

«WARNING» Failure to comply with this

information could affect the normal

operation of the equipment.

Please contact our Customer service for

further information.

SANICUBIC 1 OPERATING

PRINCIPLE

SANICUBIC

1 contains 1 pump equipped

with a high performance grinding system.

The SANICUBIC

1 tank is fitted with 3 dip

tubes; 2 tubes control the motor operation,

and the other one controls the alarm system.

- Long pickup tube (normal operation): as

soon as the waste water level in the tank

reaches the triggering point in the long

tube, the pumping system starts up.

- Short pickup tube (inflow overload

operation): if the waste water level in the

tank reaches the upper point, a contact

is activated. This contact sets off a visual

alarm on the control panel. If the external

wired alarm is connected, this would give

you an audible and visual alarm. (See

section 9)

LIST OF PARTS SUPPLIED

DIMENSIONS

TECHNICAL DATA SANICUBIC

Type R350

Maximum discharge head 36 Ft

Voltage 120 V

Frequency 60 Hz

Volume 8.5 Gallons

Maximum power input 1 HP

Maximum current input 10 A

Electrical classification I

Avg. water temp for optimum performance 104°F

Maximum temperature (intermittent) 158°F*

Protection index IP67

Net weight (including accessories) 39 IBS

Hot water drain cycles from dishwashers or washing machines

FIELDS OF APPLICATION

This system is meant for residential and

light commercial applications.

CONNECTING SANITARY

EQUIPMENT TO THE LOWER

INLETS

If you want to install a shower,

bath or even a toilet at the same

level of the Sanicubic 1, you must

make sure that the outlets of each fixture

are at least 10” above the base of the

Sanicubic 1. (ie. If connecting a rear out

let toilet to the Sanicubic 1, the back spi-

got of the bowl (cl) should be 10” above

the base of the Sanicubic 1.)

CONNECTING THE 1-

/2’’ INLETS

Lower inlets (cf.

)

Upper inlets (cf.

)

• Cut off the end of the 1-

/2’’ inlet with

a saw

• Cut the sleeve

to suit the pipe

diameter: 1-

/4’’ or 1-

/2’’ (cf.

)

• Fix the sleeve

on the inlet and on the

pipe, using the metal clamps.

CONNECTING THE 4’’ INLETS

Lower inlets (cf.

)

1- Remove the plug from the side inlet.

2- Fix the sleeve

in place using the

metal clamp.

3- Fully insert the 4’’ tube in the other end

of the sleeve and fix it in place using

the other metal clamp.

Upper inlet (cf.

)

1- Cut off the upper end of the 4’’ inlet

with a saw.

2- Fix the sleeve

in place using the

metal clamp

3- Fully insert the 4’’ tube in the other end

of the sleeve and fix it in place using

the other metal clamp

CONNECTING THE VENT

1- VENT OF SANICUBIC

The upper inlet must be used for the

vent. The vent pipe must be fitted up

to roof level.

Then fix the sleeve

in place using

the metal clamp

Fully insert the 1-

/2’’ tube in the

other end of the sleeve and fix it in

place using the other metal clamp

WARNING: Note that the vent

system should be a two-way air

vent. The use of mechanical vents,

air admittance valves or similar

devices are not permitted as these

are considered one-way air vent

systems.

The vent must be an open vent or

the unit will not operate.

2- VENTING THE ELECTRICAL SECTION

Connect the 8/11 clear PVC tubing (

)

supplied to the keyboard on the

SANICUBIC

1. The other end of this

tubing must be located between 3 Ft

and 6 Ft above the device to avoid

water getting into the electrical part

in the event of flooding.

Important: Do not pinch the tubing.

INSTALLATION

The SANICUBIC

1 must be installed in

compliance with local plumbing codes.

The equipment must be commissioned

and maintained by a qualified

professional specialist.

REGULATIONS

1- Attention: the space in which the

SANICUBIC

1 is to be installed must

be large enough to leave at least 24’’

of working room around and above

the unit to facilitate such maintenance

work as may be required. There must

be sufficient lighting, and it must be

sufficiently well ventilated and protec-

ted from freezing.

2- Isolating valves (not supplied) must

be fitted on waste inlets (especially

the 4’’ inlets) and on the discharge

to ensure that any service/

maintenance may be carried out

safely.

3- The discharge pipe must be fitted

so as to avoid all back flow from the

drainage system (see the examples

in drawing

). Back flow can be

avoided by installing an anti-back flow

riser reaching a high point above the

maximum back flow level.

Comment: In the absence of local

information to the contrary, the

maximum back flow level corresponds

to street level (roadway, pavements,

etc.). Continue the discharge pipework

after the anti-backflow riser, using a

larger diameter pipe.

4- If the SANICUBIC

1 is installed in a

space such as a pit for example, we

would recommend the fitting of a bilge

pump in case of flooding.

5- The lifting station must be vented with

an outlet at roof level.

6- The lifting station must be fixed to the

floor (see

CONNECTING THE DISCHARGE PIPE

Remove the end cover or covers from the

back of the unit.

As the motor is fitted with a grinding

system, an 1-

/2’’ discharge pipe can be

used.

The discharge bend is at the center of the

unit, at the back (cf.

). Use a standard

/2’’ coupling (not provided) to connect

it to the riser pipe and secure in place

with metal clamps.

The pump in the SANICUBIC

1 unit is

equipped with a check valve.

PERFORMANCE CURVE

RATIO OF HEIGHT/LENGTH

FOR DISCHARGE

1 2 3 4 5 6 7 8 9 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Saniflo 089 Gebrauchs- und Pflegehandbuch Seite 4

Kommentare zu diesen Handbüchern